Pre-selection for industrial process valves
INDUSTRY NEWS

DN1000 Electro-Hydraulic Slab Gate Valves Ship to an Oil-Storage Project

A DN1000, Class 300 slab gate valve package with a split electro-hydraulic actuator has shipped to an oil-storage project after shell-strength and sealing tests; the assembly is 5.8 m high and weighs 12 t.

Lead

Shengkai Engineering (胜凯工程) has shipped its first in-house electro-hydraulic slab gate valve package to an oil-storage project after completing inspection and pressure testing, the company reported through Valve Magazine's Chinese website on 3 November 2026.

Facts

The package. The reported valve is DN1000 and Class 300. The assembly is 5.8 m high and weighs 12 t, with a split electro-hydraulic actuator. (Source: the company's announcement, 2026-11-03.)

The stated duties. The valve is intended for on-off service on oil, water and steam piping at the storage project. The announcement does not assign different valve configurations to those three media. (Source: the same.)

The pressure tests. Shell-strength and sealing tests were completed before shipment. The report calls these the package's pressure-test sequence but does not publish the test pressures, holding times or measured leakage. (Source: the same.)

The seating surface. The valve-seat sealing surface uses STL hard-alloy overlay welding. The announcement attributes the choice to wear and erosion resistance but gives no material grade or thickness. (Source: the same.)

Item Published record
Valve type Electro-hydraulic slab gate valve
Nominal size DN1000
Pressure class Class 300
Assembly height 5.8 m
Assembly mass 12 t
Actuator Split electro-hydraulic unit
Reported media Oil, water and steam
Status Tested and shipped

The manufacturing record. The company states that drawing conversion, process planning, machining, assembly and pressure-test acceptance were completed within its own production sequence. The announcement identifies large-body machining, sealing-surface matching and actuator commissioning as work completed for the package. (Source: the same.)

The project status. The public record ends at shipment to the project site. It does not report installation, commissioning or entry into service. (Source: the same.)

The production sequence. Drawing conversion and process planning preceded machining and assembly in the company's account. Complete-valve pressure-test acceptance followed those manufacturing steps. This sequence records the production route used for the package rather than a general claim about other valves in the company's range. (Source: the same.)

The actuator arrangement. The actuator is described as a split electro-hydraulic unit matched to the large gate valve. The report identifies actuator matching and commissioning as completed work, but it does not publish hydraulic pressure, operating time, thrust or control-system details. (Source: the same.)

The sealing work. Machining of the large body and matching of the sealing surfaces are both identified in the manufacturing account. The STL overlay statement concerns the valve-seat sealing surface; the announcement does not describe the body, gate or stem as made entirely from that material. (Source: the same.)

The shipment preparation. The report says components were identified, protectively packed and assigned to a transport plan before shipment. Those logistics steps support the reported delivery status but do not provide a site-arrival date. (Source: the same.)

The evidence boundary. Dimensions, mass, media and test completion are published as package facts. No numerical pressure-test results or independent witness report accompany the announcement. The article therefore records that testing occurred without converting it into a quantified performance claim. (Source: the same.)

Where this connects on this site

Sources

# Basis
1 首批自主研制电液平板闸阀完成检验试验并发运;DN1000、300LB、高 5.8 米、重 12 吨;分体式电液执行器;油品、水、蒸汽切断工况;壳体与密封压力试验;STL 堆焊及制造流程 — 阀门杂志社官网(来源:胜凯工程),2026-11-03 — https://www.cvicnet.com/h-nd-5129.html

Note on sourcing. This item reports a company's manufacturing and shipment announcement carried by an industry publication. We record the stated dimensions, actuator, tests and shipment status. We do not rank or recommend suppliers.

What the source does not state

The announcement does not state the exact number of valves, the project owner, the design standard or edition, the test pressures and holding times, the actuator output, the contract value, or the delivery and commissioning dates.

Update note

This item is a dated record of a publicly reported shipment. We append corrections rather than rewrite history; corrections are marked Correction with the date.

Running a duty point? The selector on the home page maps medium, function, pressure, temperature and size to a valve type with its boundary conditions — free. Open the tool →